Products/USB UART: Difference between revisions
| (5 intermediate revisions by the same user not shown) | |||
| Line 8: | Line 8: | ||
== How-to use == | == How-to use == | ||
== Connectors == | |||
=== P1 Connector === | |||
[[Image:USB_UART_V02_P1.png|300px|right]] | |||
P1 connector is a standard 2.54mm (0.1 inch) pitch header, with 2 row of 5 pins. | |||
{| class="wikitable" | |||
!colspan="4"|P1 connector | |||
|- | |||
| Pin # | |||
| Description | |||
| FT230XS signal | |||
| Note | |||
|- | |||
| 1 | |||
| +3.3V from FT230XS | |||
| +3.3V Out | |||
| -- | |||
|- | |||
| 2 | |||
| GND - Ground | |||
| -- | |||
| -- | |||
|- | |||
| 3 | |||
| UART Tx | |||
| TxD | |||
| FT230XS pin 1 | |||
|- | |||
| 4 | |||
| UART Rx | |||
| RxD | |||
| FT230XS pin 4 | |||
|- | |||
| 5 | |||
| I2C SCL | |||
| RTS | |||
| FT230XS pin 2 | |||
|- | |||
| 6 | |||
| I2C SDA | |||
| CTS | |||
| FT230XS pin 6 | |||
|- | |||
| 7 | |||
| SPI MISO | |||
| Sleep | |||
| FT230XS pin 16 | |||
|- | |||
| 8 | |||
| SPI MOSI | |||
| TxDEN | |||
| FT230XS pin 15 | |||
|- | |||
| 9 | |||
| SPI CLK | |||
| RxLed | |||
| FT230XS pin 14 | |||
|- | |||
| 10 | |||
| SPI CS | |||
| Tx Led | |||
| FT230XS pin 7 | |||
|} | |||
=== P2 Connector === | |||
[[Image:USB_UART_V02_P2.png|300px|right]] | |||
P2 connector is a standard 2.54mm (0.1 inch) pitch header, with 1 row of 2 pins, which provides access to 5V power from USB.<br /> | |||
'''Note''' : Be careful, never connect them together as if they were for a jumper config, it would short-circuit the USB power and burn the ferite bread on the board. | |||
{| class="wikitable" | |||
!colspan="3"|P2 connector | |||
|- | |||
| Pin # | |||
| Description | |||
| Note | |||
|- | |||
| 1 | |||
| +5V | |||
| +5V from USB | |||
|- | |||
| 2 | |||
| GND | |||
| Ground | |||
|} | |||
=== P3 : micro USB debug connector === | |||
P3 is a female USB microB port.<br /> | |||
Refer to the [http://en.wikipedia.org/wiki/Universal_Serial_Bus Universal Serial Bus (USB)] page on Wikipedia for pinout and more information on the USB bus and connectors. | |||
=== P4 : USB type A debug connector === | |||
P4 is a male USB type A port.<br /> | |||
Refer to the [http://en.wikipedia.org/wiki/Universal_Serial_Bus Universal Serial Bus (USB)] page on Wikipedia for pinout and more information on the USB bus and connectors. | |||
== TODO List == | == TODO List == | ||
| Line 24: | Line 115: | ||
* 24mm x 30mm | * 24mm x 30mm | ||
* Two USB connectors (USB type A male and micro-USB B female) | * Two USB connectors (USB type A male and micro-USB B female) | ||
* 6 pins on P1 connector (standard 2.54mm (0.1 inch) pitch header, with 2 | * Two push buttons for ISP/Reset | ||
* 6 pins on P1 connector (standard 2.54mm (0.1 inch) pitch header, with 2 rows of 3 pins). | |||
{| class="wikitable" | {| class="wikitable" | ||
!colspan=" | !colspan="4"|P1 connector | ||
|- | |- | ||
| Pin # | | Pin # | ||
| Line 43: | Line 135: | ||
| -- | | -- | ||
|- | |- | ||
|3 | | 3 | ||
| UART Tx | | UART Tx | ||
| TxD | | TxD | ||
| -- | | -- | ||
|- | |- | ||
|4 | | 4 | ||
| UART Rx | | UART Rx | ||
| RxD | | RxD | ||
| -- | | -- | ||
|- | |- | ||
|5 | | 5 | ||
| Reset | | Reset | ||
| RTS | | RTS | ||
| Also connected to SW1 push button | | Also connected to SW1 push button | ||
|- | |- | ||
|6 | | 6 | ||
| ISP | | ISP | ||
| TxDEN | | TxDEN | ||
| Also connected to SW2 push button | | Also connected to SW2 push button | ||
|} | |} | ||
=== V0.2 === | |||
Second (and current) version. | |||
* 18mm x 30mm | |||
* Two USB connectors (USB type A male and micro-USB B female) | |||
* Removed push buttons | |||
* 10 pins on P1 connector (standard 2.54mm (0.1 inch) pitch header, with 2 rows of 5 pins). | |||
* Access to USB power on P2 connector (standard 2.54mm (0.1 inch) pitch header, with 1 row of 2 pins). | |||
Latest revision as of 01:57, 25 March 2021
Description
The USB-UART adapter is pretty simple but usefull and ressourcefull. It provides access to a serial link (3.3V UART) from an USB port, either USB male or micro-USB female which is one of the cool special features of this adapter. Another cool feature is the 3.3V and 5V power both available on 2.54mm headers, usefull for most prototyping needs.
This adapter uses an FTDI FT230XS, with most signals available on the UEXT-like connector, and should thus support I2C, SPI, and other protocols or data busses using the bitbanging capabilities of the FTDI chips, though this would require software support on your side as we did not have time to do so yet (We'll keep you up-to-date as soon as we have more information on these).
How-to use
Connectors
P1 Connector
P1 connector is a standard 2.54mm (0.1 inch) pitch header, with 2 row of 5 pins.
| P1 connector | |||
|---|---|---|---|
| Pin # | Description | FT230XS signal | Note |
| 1 | +3.3V from FT230XS | +3.3V Out | -- |
| 2 | GND - Ground | -- | -- |
| 3 | UART Tx | TxD | FT230XS pin 1 |
| 4 | UART Rx | RxD | FT230XS pin 4 |
| 5 | I2C SCL | RTS | FT230XS pin 2 |
| 6 | I2C SDA | CTS | FT230XS pin 6 |
| 7 | SPI MISO | Sleep | FT230XS pin 16 |
| 8 | SPI MOSI | TxDEN | FT230XS pin 15 |
| 9 | SPI CLK | RxLed | FT230XS pin 14 |
| 10 | SPI CS | Tx Led | FT230XS pin 7 |
P2 Connector
P2 connector is a standard 2.54mm (0.1 inch) pitch header, with 1 row of 2 pins, which provides access to 5V power from USB.
Note : Be careful, never connect them together as if they were for a jumper config, it would short-circuit the USB power and burn the ferite bread on the board.
| P2 connector | ||
|---|---|---|
| Pin # | Description | Note |
| 1 | +5V | +5V from USB |
| 2 | GND | Ground |
P3 : micro USB debug connector
P3 is a female USB microB port.
Refer to the Universal Serial Bus (USB) page on Wikipedia for pinout and more information on the USB bus and connectors.
P4 : USB type A debug connector
P4 is a male USB type A port.
Refer to the Universal Serial Bus (USB) page on Wikipedia for pinout and more information on the USB bus and connectors.
TODO List
- Technical documentation
- I2C and SPI support using the bit-banging capabilities of the FTDI chip (Host side software support)
- SWD and/or JTAG support
- RS232 version
- Low voltage (1.8V) version (microprocessors and SWD/JTAG debug support)
Technical Documentation and Schematics
The technical documentation has not been written yet ...
Version history
V0.1
First version.
- 24mm x 30mm
- Two USB connectors (USB type A male and micro-USB B female)
- Two push buttons for ISP/Reset
- 6 pins on P1 connector (standard 2.54mm (0.1 inch) pitch header, with 2 rows of 3 pins).
| P1 connector | |||
|---|---|---|---|
| Pin # | Description | FT230XS signal | Note |
| 1 | +3.3V from FT230XS | +3.3V Out | -- |
| 2 | GND - Ground | -- | -- |
| 3 | UART Tx | TxD | -- |
| 4 | UART Rx | RxD | -- |
| 5 | Reset | RTS | Also connected to SW1 push button |
| 6 | ISP | TxDEN | Also connected to SW2 push button |
V0.2
Second (and current) version.
- 18mm x 30mm
- Two USB connectors (USB type A male and micro-USB B female)
- Removed push buttons
- 10 pins on P1 connector (standard 2.54mm (0.1 inch) pitch header, with 2 rows of 5 pins).
- Access to USB power on P2 connector (standard 2.54mm (0.1 inch) pitch header, with 1 row of 2 pins).